BearingCupVersionTwo: Difference between revisions
Jump to navigation
Jump to search
| Line 219: | Line 219: | ||
G2 X1.14 Y15.71 I14.01 J7.2 (C to D) | G2 X1.14 Y15.71 I14.01 J7.2 (C to D) | ||
G2 X14.01 Y7.2 I6.86 J-3.62 (D to A) | G2 X14.01 Y7.2 I6.86 J-3.62 (D to A) | ||
G1 X20 Y7.2 | |||
G1 Z-4 (feed to | G1 Z-4 (feed to 4mm below surface) | ||
G2 X-1.14 Y-15.71 I-14.01 J-7.2 (A to B) | G2 X-1.14 Y-15.71 I-14.01 J-7.2 (A to B) | ||
G2 X-14.01 Y-7.2 I-6.86 J3.62 (B to C) | G2 X-14.01 Y-7.2 I-6.86 J3.62 (B to C) | ||
G2 X1.14 Y15.71 I14.01 J7.2 (C to D) | G2 X1.14 Y15.71 I14.01 J7.2 (C to D) | ||
G2 X14.01 Y7.2 I6.86 J-3.62 (D to A) | G2 X14.01 Y7.2 I6.86 J-3.62 (D to A) | ||
G1 X20 Y7.2 | |||
G1 Z-6 (feed to | G1 Z-6 (feed to 6mm below surface) | ||
G2 X-1.14 Y-15.71 I-14.01 J-7.2 (A to B) | G2 X-1.14 Y-15.71 I-14.01 J-7.2 (A to B) | ||
G2 X-14.01 Y-7.2 I-6.86 J3.62 (B to C) | G2 X-14.01 Y-7.2 I-6.86 J3.62 (B to C) | ||
G2 X1.14 Y15.71 I14.01 J7.2 (C to D) | G2 X1.14 Y15.71 I14.01 J7.2 (C to D) | ||
G2 X14.01 Y7.2 I6.86 J-3.62 (D to A) | G2 X14.01 Y7.2 I6.86 J-3.62 (D to A) | ||
G1 X20 Y7.2 | |||
G1 Z-8 (feed to | G1 Z-8 (feed to 8mm below surface) | ||
G2 X-1.14 Y-15.71 I-14.01 J-7.2 (A to B) | G2 X-1.14 Y-15.71 I-14.01 J-7.2 (A to B) | ||
G2 X-14.01 Y-7.2 I-6.86 J3.62 (B to C) | G2 X-14.01 Y-7.2 I-6.86 J3.62 (B to C) | ||
G2 X1.14 Y15.71 I14.01 J7.2 (C to D) | G2 X1.14 Y15.71 I14.01 J7.2 (C to D) | ||
G2 X14.01 Y7.2 I6.86 J-3.62 (D to A) | G2 X14.01 Y7.2 I6.86 J-3.62 (D to A) | ||
G1 X20 Y7.2 | |||
G1 Z-9 (feed to | G1 Z-9 (feed to 9mm below surface) | ||
G2 X-1.14 Y-15.71 I-14.01 J-7.2 (A to B) | G2 X-1.14 Y-15.71 I-14.01 J-7.2 (A to B) | ||
G2 X-14.01 Y-7.2 I-6.86 J3.62 (B to C) | G2 X-14.01 Y-7.2 I-6.86 J3.62 (B to C) | ||
G2 X1.14 Y15.71 I14.01 J7.2 (C to D) | G2 X1.14 Y15.71 I14.01 J7.2 (C to D) | ||
G2 X14.01 Y7.2 I6.86 J-3.62 (D to A) | G2 X14.01 Y7.2 I6.86 J-3.62 (D to A) | ||
G1 X20 Y7.2 | |||
G1 X20 Y7.23 (feed to starting point) | |||
;; Finish Cut for Perimeter | ;; Finish Cut for Perimeter | ||
| Line 254: | Line 254: | ||
G2 X1.14 Y15.71 I14.01 J7.2 (C to D) | G2 X1.14 Y15.71 I14.01 J7.2 (C to D) | ||
G2 X14.01 Y7.2 I6.86 J-3.62 (D to A) | G2 X14.01 Y7.2 I6.86 J-3.62 (D to A) | ||
G1 X20 Y7.23 | |||
G0 Z20 (traverse to 20mm above) | G0 Z20 (traverse to 20mm above) | ||
M30 (end of program) | M30 (end of program) | ||
</pre> | </pre> | ||
= Release Part = | = Release Part = | ||
<pre> | <pre> | ||
Revision as of 06:25, 22 July 2022
Drill Ears
;; ------------------------------ ;; Drill Ears (001) ;; ------------------------------ ;; Use 1/2" x 2" rectangle 6061 T6, at least 28mm long. ;; Spindle RPM to 1200 ;; Zero X to 14mm in from right end ;; Zero Y to middle of material ;; Insert Appropriate drill bit (.166 for slip, M4-0.7 tap drill bit for threads) ;; Zero Z to shoulder of drill bit ;; Check H128 for zero offset ;; Check T128 for zero diameter G21 (set units to millimeters) G90 (set measurements to absolute, relative to machine zero) F60 (set feed rate to 60mm per minute, 0.025 mm per tooth) T128 (tool with zero height and diameter) G43 H128 (height offset zero) G0 Z20 (traverse to 20mm above part) G0 X8 Y12.09 (traverse to screw hole center XY) G0 Z5 (traverse to 5mm above) G1 Z-5 (peck to 5mm deep) G0 Z6 (retract to 6mm above) G0 Z0 (traverse to 0mm above) G1 Z-10 (peck to 10mm deep - top has not been faced yet) G0 Z20 (traverse to 20mm above) M30 (end of program)
Drill Center
;; ------------------------------------ ;; Drill Center, Starter Bit (002) ;; ------------------------------------ ;; Insert 5/16" or 8mm drill bit ;; Zero Z to shoulder of drill bit G21 (set units to millimeters) G90 (set measurements to absolute, relative to machine zero) F60 (set feed rate to 60mm per minute, 0.025 mm per tooth) T128 (tool with zero height and diameter) G43 H128 (height offset zero) G0 Z20 (traverse to 20mm above part) G0 X0 Y0 (traverse to screw hole center XY) G0 Z5 (traverse to 5mm above) G1 Z-5 (peck to 5mm deep) G0 Z6 (retract to 6mm above) G0 Z0 (traverse to 0mm above) G1 Z-10 (peck to 10mm deep - top has not been faced yet) G0 Z20 (traverse to 20mm above) M30 (end of program)
;; ------------------------------------ ;; Drill Center, Final Bit (003) ;; ------------------------------------ ;; Insert 1/2" or 13mm drill bit ;; Zero Z to shoulder of drill bit G21 (set units to millimeters) G90 (set measurements to absolute, relative to machine zero) F60 (set feed rate to 60mm per minute, 0.025 mm per tooth) T128 (tool with zero height and diameter) G43 H128 (height offset zero) G0 Z20 (traverse to 20mm above part) G0 X0 Y0 (traverse to screw hole center XY) G0 Z5 (traverse to 5mm above) G1 Z-5 (peck to 5mm deep) G0 Z6 (retract to 6mm above) G0 Z0 (traverse to 0mm above) G1 Z-10 (peck to 10mm deep - top has not been faced yet) G0 Z20 (traverse to 20mm above) M30 (end of program)
Face Part
;; ---------------------------------------- ;; Face Part (004) ;; ---------------------------------------- ;; Insert 6mm carbide square end mill ;; Set RPM to 5,000, 300 SFM ;; Zero Z to a grazing cut. G21 (set units to millimeters) G90 (set measurements to absolute, relative to machine zero) F500 (set feed speed to 500mm per minute, 0.025 mm per tooth) T128 (tool with zero height and diameter) G43 H128 (height offset zero) G0 Z20 (traverse to 20mm above part) G17 (set XY coordinate system for arc cuts) G0 X20 Y0.56 (traverse to outside part) G0 Z5 (traverse to 5mm above part) G1 Z0 (feed to grazing cut) G1 X6.34 Y9.59 (feed to start of upper right ear) G2 X6.34 Y9.59 I1.66 J2.5 (CW arc cut to same position about upper right ear) G3 X-6.34 Y-9.59 I-6.34 J-9.59 (CCW arc cut to lower left ear about origin) G2 X-6.34 Y-9.59 I-1.66 J-2.5 (CW arc cut to same position about lower left ear) G3 X6.34 Y9.59 I6.34 J9.59 (CCW arc cut back to where we stared about origin) G0 Z20 (traverse to 20mm above) M30 (end of program)
Round Pocket in Center
;; -------------------------------------- ;; Round Pocket in Center (005) ;; -------------------------------------- G21 (set units to millimeters) G90 (set measurements to absolute, relative to machine zero) F500 (set feed speed to 500mm per minute, 0.025 mm per tooth) T128 (tool with zero height and diameter) G43 H128 (height offset zero) G0 Z20 (traverse to 20mm above) G0 X0 Y0 (traverse to starting point) ;; Rough Cut for Retainer G0 Z5 (traverse to 5mm above part) G1 Z-2 (2mm below surface) G1 X5.75 Y0 (8.75mm R / 17.5 mm D) G3 X5.75 Y0 I-5.75 J0 (circle about origin) G1 X0 Y0 G1 Z-4 (4mm below surface) G1 X5.75 Y0 (8.75mm R / 17.5 mm D) G3 X5.75 Y0 I-5.75 J0 (circle about origin) G1 X0 Y0 G1 Z-6 (6mm below surface) G1 X5.75 Y0 (8.75mm R / 17.5 mm D) G3 X5.75 Y0 I-5.75 J0 (circle about origin) G1 X0 Y0 G1 Z-8 (8mm below surface) G1 X5.75 Y0 (8.75mm R / 17.5 mm D) G3 X5.75 Y0 I-5.75 J0 (circle about origin) G1 X0 Y0 G1 Z-9 (9mm below surface) G1 X5.75 Y0 (8.75mm R / 17.5 mm D) G3 X5.75 Y0 I-5.75 J0 (circle about center) G1 X0 Y0 ;; Rough Cut for Bearing Cup G0 Z5 (traverse to 5mm above part) G1 Z-2 (2mm below surface) G1 X7.75 Y0 (10.75mm R / 21.5 mm D) G3 X7.75 Y0 I-7.75 J0 (circle about origin) G1 X0 Y0 G1 Z-4 (4mm below surface) G1 X7.75 Y0 (10.75mm R / 21.5 mm D) G3 X7.75 Y0 I-7.75 J0 (circle about origin) G1 X0 Y0 G1 Z-6 (6mm below surface) G1 X7.75 Y0 (10.75mm R / 21.5 mm D) G3 X7.75 Y0 I-7.75 J0 (circle about origin) G1 X0 Y0 G1 Z-6.85 (6.85mm below surface) G1 X7.80 Y0 (10.80mm R / 21.6 mm D) G3 X7.80 Y0 I-7.80 J0 (circle about origin) G1 X0 Y0 ;; Finish Cut for Retainer G0 X0 Y0 (traverse to origin XY) F200 (set feed speed to 200mm per minute, 0.010 mm per tooth) G1 Z-9 (feed to 9mm below part) G1 X6 Y0 (9mm R / 18mm D) G3 X6 Y0 I-6 J0 (circle about origin) G1 X0 Y0 ;; Finish Cut for Bearing Cup G0 X0 Y0 (traverse to origin XY) F200 (set feed speed to 200mm per minute, 0.010 mm per tooth) G1 Z-7.1 (feed to 7.1mm below surface) G1 X8.05 Y0 (11.05mm R / 22.1mm D) G3 X8.05 Y0 I-8.05 J0 (circle about origin) G1 X0 Y0 G0 Z20 (traverse to 20mm above) M30 (end of program)
Perimeter Cut
;; -------------------------------------- ;; Perimeter Cut (006) ;; -------------------------------------- G21 (set units to millimeters) G90 (set measurements to absolute, relative to machine zero) F500 (set feed speed to 500mm per minute, 0.025 mm per tooth) T128 (tool with zero height and diameter) G43 H128 (height offset zero) G0 Z20 (traverse to 20mm above) G0 X20 Y7.2 (traverse to starting point) G0 Z5 (traverse to 5mm above part) ;; Rough Cut for Perimeter G1 Z-2 (feed to 2mm below surface) G2 X-1.14 Y-15.71 I-14.01 J-7.2 (A to B) G2 X-14.01 Y-7.2 I-6.86 J3.62 (B to C) G2 X1.14 Y15.71 I14.01 J7.2 (C to D) G2 X14.01 Y7.2 I6.86 J-3.62 (D to A) G1 X20 Y7.2 G1 Z-4 (feed to 4mm below surface) G2 X-1.14 Y-15.71 I-14.01 J-7.2 (A to B) G2 X-14.01 Y-7.2 I-6.86 J3.62 (B to C) G2 X1.14 Y15.71 I14.01 J7.2 (C to D) G2 X14.01 Y7.2 I6.86 J-3.62 (D to A) G1 X20 Y7.2 G1 Z-6 (feed to 6mm below surface) G2 X-1.14 Y-15.71 I-14.01 J-7.2 (A to B) G2 X-14.01 Y-7.2 I-6.86 J3.62 (B to C) G2 X1.14 Y15.71 I14.01 J7.2 (C to D) G2 X14.01 Y7.2 I6.86 J-3.62 (D to A) G1 X20 Y7.2 G1 Z-8 (feed to 8mm below surface) G2 X-1.14 Y-15.71 I-14.01 J-7.2 (A to B) G2 X-14.01 Y-7.2 I-6.86 J3.62 (B to C) G2 X1.14 Y15.71 I14.01 J7.2 (C to D) G2 X14.01 Y7.2 I6.86 J-3.62 (D to A) G1 X20 Y7.2 G1 Z-9 (feed to 9mm below surface) G2 X-1.14 Y-15.71 I-14.01 J-7.2 (A to B) G2 X-14.01 Y-7.2 I-6.86 J3.62 (B to C) G2 X1.14 Y15.71 I14.01 J7.2 (C to D) G2 X14.01 Y7.2 I6.86 J-3.62 (D to A) G1 X20 Y7.2 G1 X20 Y7.23 (feed to starting point) ;; Finish Cut for Perimeter F200 (set feed speed to 200mm per minute, 0.010 mm per tooth) G1 Z-9 (feed to 9mm below part) G2 X-1.14 Y-15.71 I-14.01 J-7.2 (A to B) G2 X-14.01 Y-7.2 I-6.86 J3.62 (B to C) G2 X1.14 Y15.71 I14.01 J7.2 (C to D) G2 X14.01 Y7.2 I6.86 J-3.62 (D to A) G1 X20 Y7.23 G0 Z20 (traverse to 20mm above) M30 (end of program)
Release Part
;; ---------------------------------------- ;; Release Part (007) ;; ---------------------------------------- ;; Insert 6mm carbide square end mill ;; Set RPM to 5,000, 300 SFM ;; Flip Material Front to Back ;; Zero X to 14mm in from right end of material ;; Zero Y to middle of part (should be unchanged) ;; Zero Z to desired depth of cut. G21 (set units to millimeters) G90 (set measurements to absolute, relative to machine zero) F500 (set feed speed to 500mm per minute, 0.025 mm per tooth) T128 (tool with zero height and diameter) G43 H128 (height offset zero) G0 Z20 (traverse to 20mm above part) G17 (set XY coordinate system for arc cuts) G0 X20 Y-0.56 (traverse to outside part) G0 Z5 (traverse to 5mm above part) G1 Z2 (feed to 2mm above final cut) G1 X6.34 Y-9.59 (feed to start of upper right ear) G3 X6.34 Y-9.59 I1.66 J-2.5 (CCW arc cut to same position about upper right ear) G2 X-6.34 Y9.59 I-6.34 J9.59 (CW arc cut to lower left ear about origin) G3 X-6.34 Y9.59 I-1.66 J2.5 (CCW arc cut to same position about lower left ear) G2 X6.34 Y-9.59 I6.34 J-9.59 (CW arc cut back to where we stared about origin) G1 X20 Y-0.56 (feed to outside part) G1 Z1 (feed to 1mm above final cut) G1 X6.34 Y-9.59 (feed to start of upper right ear) G3 X6.34 Y-9.59 I1.66 J-2.5 (CCW arc cut to same position about upper right ear) G2 X-6.34 Y9.59 I-6.34 J9.59 (CW arc cut to lower left ear about origin) G3 X-6.34 Y9.59 I-1.66 J2.5 (CCW arc cut to same position about lower left ear) G2 X6.34 Y-9.59 I6.34 J-9.59 (CW arc cut back to where we stared about origin) G1 X20 Y-0.56 (feed to outside part) G1 Z0 (feed to 1mm above final cut) G1 X6.34 Y-9.59 (feed to start of upper right ear) G3 X6.34 Y-9.59 I1.66 J-2.5 (CCW arc cut to same position about upper right ear) G2 X-6.34 Y9.59 I-6.34 J9.59 (CW arc cut to lower left ear about origin) G3 X-6.34 Y9.59 I-1.66 J2.5 (CCW arc cut to same position about lower left ear) G2 X6.34 Y-9.59 I6.34 J-9.59 (CW arc cut back to where we stared about origin) G1 X20 Y-0.56 (feed to outside part) G0 Z20 (traverse to 20mm above) M30 (end of program)