BearingCupVersionTwo: Difference between revisions

From Traxel Wiki
Jump to navigation Jump to search
No edit summary
Line 109: Line 109:
G0 X20 Y0.56 (traverse to outside part)
G0 X20 Y0.56 (traverse to outside part)
G0 Z5 (traverse to 5mm above part)
G0 Z5 (traverse to 5mm above part)
G1 Z0.1 (feed to 0.1 above grazing cut)
G1 X6.34 Y9.59 (feed to start of upper right ear)
G1 Z0 (feed to grazing cut)
G1 Z0 (feed to grazing cut)
G1 X6.34 Y9.59 (feed to start of upper right ear)
G2 X6.34 Y9.59 I1.66 J2.5 (CW arc cut to same position about upper right ear)
G2 X6.34 Y9.59 I1.66 J2.5 (CW arc cut to same position about upper right ear)
G3 X-6.34 Y-9.59 I-6.34 J-9.59 (CCW arc cut to lower left ear about origin)
G3 X-6.34 Y-9.59 I-6.34 J-9.59 (CCW arc cut to lower left ear about origin)

Revision as of 16:33, 22 July 2022

BearingCupVersionOne

Drill Ears

;; ------------------------------
;; Drill Ears (001)
;; ------------------------------
;; Use 1/2" x 2" rectangle 6061 T6, at least 28mm long.
;; Spindle RPM to 1200
;; Zero X to 14mm in from right end
;; Zero Y to middle of material
;; Insert Appropriate drill bit (.166 for slip, M4-0.7 tap drill bit for threads)
;; Zero Z to shoulder of drill bit
;; Check H64 in CNC control system for zero offset
;; Check T64 in CNC control system for zero diameter

G21 (set units to millimeters)
G90 (set measurements to absolute, relative to machine zero)
F60 (set feed rate to 60mm per minute, 0.025 mm per tooth)
T64 (set tool with zero height and diameter)
G43 H64 (set height offset zero)

G0 Z20 (traverse to 20mm above part)

G0 X8 Y12.09 (traverse to screw hole center XY)
G0 Z5 (traverse to 5mm above)
G1 Z-5 (peck to 5mm deep)
G0 Z6 (retract to 6mm above)
G0 Z0 (traverse to 0mm above)
G1 Z-10 (peck to 10mm deep - top has not been faced yet)

G0 Z20 (traverse to 20mm above)

M30 (end of program)

Drill Center

;; ------------------------------------
;; Drill Center, Starter Bit (002)
;; ------------------------------------
;; Insert 5/16" or 8mm drill bit
;; Zero Z to shoulder of drill bit

G21 (set units to millimeters)
G90 (set measurements to absolute, relative to machine zero)
F60 (set feed rate to 60mm per minute, 0.025 mm per tooth)
T64 (tool with zero height and diameter)
G43 H64 (height offset zero)

G0 Z20 (traverse to 20mm above part)

G0 X0 Y0 (traverse to screw hole center XY)
G0 Z5 (traverse to 5mm above)
G1 Z-5 (peck to 5mm deep)
G0 Z6 (retract to 6mm above)
G0 Z0 (traverse to 0mm above)
G1 Z-10 (peck to 10mm deep - top has not been faced yet)

G0 Z20 (traverse to 20mm above)

M30 (end of program)
;; ------------------------------------
;; Drill Center, Final Bit (003)
;; ------------------------------------
;; Insert 1/2" or 13mm drill bit
;; Zero Z to shoulder of drill bit

G21 (set units to millimeters)
G90 (set measurements to absolute, relative to machine zero)
F60 (set feed rate to 60mm per minute, 0.025 mm per tooth)
T64 (tool with zero height and diameter)
G43 H64 (height offset zero)

G0 Z20 (traverse to 20mm above part)

G0 X0 Y0 (traverse to screw hole center XY)
G0 Z5 (traverse to 5mm above)
G1 Z-5 (peck to 5mm deep)
G0 Z6 (retract to 6mm above)
G0 Z0 (traverse to 0mm above)
G1 Z-10 (peck to 10mm deep - top has not been faced yet)

G0 Z20 (traverse to 20mm above)

M30 (end of program)

Face Part

;; ----------------------------------------
;; Face Part (004)
;; ----------------------------------------
;; Insert 6mm carbide square end mill
;; Set RPM to 5,000, 300 SFM
;; Zero Z to a grazing cut.

G21 (set units to millimeters)
G90 (set measurements to absolute, relative to machine zero)
F500 (set feed speed to 500mm per minute, 0.025 mm per tooth)
T64 (tool with zero height and diameter)
G43 H64 (height offset zero)

G0 Z20 (traverse to 20mm above part)

G17 (set XY coordinate system for arc cuts)

G0 X20 Y0.56 (traverse to outside part)
G0 Z5 (traverse to 5mm above part)
G1 Z0.1 (feed to 0.1 above grazing cut)
G1 X6.34 Y9.59 (feed to start of upper right ear)
G1 Z0 (feed to grazing cut)
G2 X6.34 Y9.59 I1.66 J2.5 (CW arc cut to same position about upper right ear)
G3 X-6.34 Y-9.59 I-6.34 J-9.59 (CCW arc cut to lower left ear about origin)
G2 X-6.34 Y-9.59 I-1.66 J-2.5 (CW arc cut to same position about lower left ear)
G3 X6.34 Y9.59 I6.34 J9.59 (CCW arc cut back to where we stared about origin)

G0 Z20 (traverse to 20mm above)
M30 (end of program)

Round Pocket in Center

;; --------------------------------------
;; Round Pocket in Center (005)
;; --------------------------------------
G21 (set units to millimeters)
G90 (set measurements to absolute, relative to machine zero)
F500 (set feed speed to 500mm per minute, 0.025 mm per tooth)
T64 (tool with zero height and diameter)
G43 H64 (height offset zero)
G17 (set XY coordinate system for arc cuts)

G0 Z20 (traverse to 20mm above)

G0 X0 Y0 (traverse to starting point)

;; Rough Cut for Retainer
G0 Z5 (traverse to 5mm above part)
G1 Z-2 (2mm below surface)
G1 X5.75 Y0 (8.75mm R / 17.5 mm D)
G3 X5.75 Y0 I-5.75 J0 (circle about origin)
G1 X0 Y0
G1 Z-4 (4mm below surface)
G1 X5.75 Y0 (8.75mm R / 17.5 mm D)
G3 X5.75 Y0 I-5.75 J0 (circle about origin)
G1 X0 Y0
G1 Z-6 (6mm below surface)
G1 X5.75 Y0 (8.75mm R / 17.5 mm D)
G3 X5.75 Y0 I-5.75 J0 (circle about origin)
G1 X0 Y0
G1 Z-8 (8mm below surface)
G1 X5.75 Y0 (8.75mm R / 17.5 mm D)
G3 X5.75 Y0 I-5.75 J0 (circle about origin)
G1 X0 Y0
G1 Z-9 (9mm below surface)
G1 X5.75 Y0 (8.75mm R / 17.5 mm D)
G3 X5.75 Y0 I-5.75 J0 (circle about center)
G1 X0 Y0

;; Rough Cut for Bearing Cup
G0 Z5 (traverse to 5mm above part)
G1 Z-2 (2mm below surface)
G1 X7.75 Y0 (10.75mm R / 21.5 mm D)
G3 X7.75 Y0 I-7.75 J0 (circle about origin)
G1 X0 Y0
G1 Z-4 (4mm below surface)
G1 X7.75 Y0 (10.75mm R / 21.5 mm D)
G3 X7.75 Y0 I-7.75 J0 (circle about origin)
G1 X0 Y0
G1 Z-6 (6mm below surface)
G1 X7.75 Y0 (10.75mm R / 21.5 mm D)
G3 X7.75 Y0 I-7.75 J0 (circle about origin)
G1 X0 Y0
G1 Z-6.85 (6.85mm below surface)
G1 X7.80 Y0 (10.80mm R / 21.6 mm D)
G3 X7.80 Y0 I-7.80 J0 (circle about origin)
G1 X0 Y0

;; Finish Cut for Retainer
G0 X0 Y0 (traverse to origin XY)
F200 (set feed speed to 200mm per minute, 0.010 mm per tooth)
G1 Z-9 (feed to 9mm below part)
G1 X6 Y0 (9mm R / 18mm D)
G3 X6 Y0 I-6 J0 (circle about origin)
G1 X0 Y0

;; Finish Cut for Bearing Cup
G0 X0 Y0 (traverse to origin XY)
F200 (set feed speed to 200mm per minute, 0.010 mm per tooth)
G1 Z-7.1 (feed to 7.1mm below surface)
G1 X8.05 Y0 (11.05mm R / 22.1mm D)
G3 X8.05 Y0 I-8.05 J0 (circle about origin)
G1 X0 Y0

G0 Z20 (traverse to 20mm above)
M30 (end of program)

Perimeter Cut

;; --------------------------------------
;; Perimeter Cut (006)
;; --------------------------------------
G21 (set units to millimeters)
G90 (set measurements to absolute, relative to machine zero)
F500 (set feed speed to 500mm per minute, 0.025 mm per tooth)
T64 (tool with zero height and diameter)
G43 H64 (height offset zero)
G17 (set XY coordinate system for arc cuts)

G0 Z20 (traverse to 20mm above)

G0 X20 Y7.2 (traverse to starting point)
G0 Z5 (traverse to 5mm above part)

;; Rough Cut for Perimeter
G1 Z-2 (feed to 2mm below surface)
G2 X-1.14 Y-15.71 I-14.01 J-7.2 (A to B)
G2 X-14.01 Y-7.2 I-6.86 J3.62 (B to C)
G2 X1.14 Y15.71 I14.01 J7.2 (C to D)
G2 X14.01 Y7.2 I6.86 J-3.62 (D to A)
G1 X20 Y7.2
G1 Z-4 (feed to 4mm below surface)
G2 X-1.14 Y-15.71 I-14.01 J-7.2 (A to B)
G2 X-14.01 Y-7.2 I-6.86 J3.62 (B to C)
G2 X1.14 Y15.71 I14.01 J7.2 (C to D)
G2 X14.01 Y7.2 I6.86 J-3.62 (D to A)
G1 X20 Y7.2
G1 Z-6 (feed to 6mm below surface)
G2 X-1.14 Y-15.71 I-14.01 J-7.2 (A to B)
G2 X-14.01 Y-7.2 I-6.86 J3.62 (B to C)
G2 X1.14 Y15.71 I14.01 J7.2 (C to D)
G2 X14.01 Y7.2 I6.86 J-3.62 (D to A)
G1 X20 Y7.2
G1 Z-8 (feed to 8mm below surface)
G2 X-1.14 Y-15.71 I-14.01 J-7.2 (A to B)
G2 X-14.01 Y-7.2 I-6.86 J3.62 (B to C)
G2 X1.14 Y15.71 I14.01 J7.2 (C to D)
G2 X14.01 Y7.2 I6.86 J-3.62 (D to A)
G1 X20 Y7.2
G1 Z-9 (feed to 9mm below surface)
G2 X-1.14 Y-15.71 I-14.01 J-7.2 (A to B)
G2 X-14.01 Y-7.2 I-6.86 J3.62 (B to C)
G2 X1.14 Y15.71 I14.01 J7.2 (C to D)
G2 X14.01 Y7.2 I6.86 J-3.62 (D to A)
G1 X20 Y7.2

G1 X20 Y7.23 (feed to starting point)

;; Finish Cut for Perimeter
F200 (set feed speed to 200mm per minute, 0.010 mm per tooth)
G1 Z-9 (feed to 9mm below part)
G2 X-1.14 Y-15.71 I-14.01 J-7.2 (A to B)
G2 X-14.01 Y-7.2 I-6.86 J3.62 (B to C)
G2 X1.14 Y15.71 I14.01 J7.2 (C to D)
G2 X14.01 Y7.2 I6.86 J-3.62 (D to A)
G1 X20 Y7.23

G0 Z20 (traverse to 20mm above)
M30 (end of program)

Release Part

;; ----------------------------------------
;; Release Part (007)
;; ----------------------------------------
;; Insert 6mm carbide square end mill
;; Set RPM to 5,000, 300 SFM
;; Flip Material Front to Back
;; Zero X to 14mm in from right end of material
;; Zero Y to middle of part (should be unchanged)
;; Zero Z to 4mm above desired depth of cut (should be close to surface)

G21 (set units to millimeters)
G90 (set measurements to absolute, relative to machine zero)
F500 (set feed speed to 500mm per minute, 0.025 mm per tooth)
T64 (tool with zero height and diameter)
G43 H64 (height offset zero)
G17 (set XY coordinate system for arc cuts)

G0 Z20 (traverse to 20mm above part)

G0 X20 Y-0.56 (traverse to outside part)
G0 Z5 (traverse to 5mm above part)

G1 Z-1 (feed to 1mm below surface)
G1 X6.34 Y-9.59 (feed to start of upper right ear)
G3 X6.34 Y-9.59 I1.66 J-2.5 (CCW arc cut to same position about upper right ear)
G2 X-6.34 Y9.59 I-6.34 J9.59 (CW arc cut to lower left ear about origin)
G3 X-6.34 Y9.59 I-1.66 J2.5 (CCW arc cut to same position about lower left ear)
G2 X6.34 Y-9.59 I6.34 J-9.59 (CW arc cut back to where we stared about origin)
G1 X20 Y-0.56 (feed to outside part)

G1 Z-3 (feed to 3mm below surface)
G1 X6.34 Y-9.59 (feed to start of upper right ear)
G3 X6.34 Y-9.59 I1.66 J-2.5 (CCW arc cut to same position about upper right ear)
G2 X-6.34 Y9.59 I-6.34 J9.59 (CW arc cut to lower left ear about origin)
G3 X-6.34 Y9.59 I-1.66 J2.5 (CCW arc cut to same position about lower left ear)
G2 X6.34 Y-9.59 I6.34 J-9.59 (CW arc cut back to where we stared about origin)
G1 X20 Y-0.56 (feed to outside part)

F200 (slow feed to 200mm, 0.010mm per tooth)

G1 Z-3.5 (feed to 3.5mm below surface)
G1 X6.34 Y-9.59 (feed to start of upper right ear)
G3 X6.34 Y-9.59 I1.66 J-2.5 (CCW arc cut to same position about upper right ear)
G2 X-6.34 Y9.59 I-6.34 J9.59 (CW arc cut to lower left ear about origin)
G3 X-6.34 Y9.59 I-1.66 J2.5 (CCW arc cut to same position about lower left ear)
G2 X6.34 Y-9.59 I6.34 J-9.59 (CW arc cut back to where we stared about origin)
G1 X20 Y-0.56 (feed to outside part)

G1 Z-4 (feed to 4mm above final cut)
G1 X6.34 Y-9.59 (feed to start of upper right ear)
G3 X6.34 Y-9.59 I1.66 J-2.5 (CCW arc cut to same position about upper right ear)
G2 X-6.34 Y9.59 I-6.34 J9.59 (CW arc cut to lower left ear about origin)
G3 X-6.34 Y9.59 I-1.66 J2.5 (CCW arc cut to same position about lower left ear)
G2 X6.34 Y-9.59 I6.34 J-9.59 (CW arc cut back to where we stared about origin)
G1 X20 Y-0.56 (feed to outside part)

G0 Z20 (traverse to 20mm above)
M30 (end of program)